Clik here to view.
Error with launching Python Script Via AWRDE VBA Script
Hello Team,I am currently following this AWR script posted on them, to run a python script directly from inside AWR using VBA script.Launching Python from AWRDE VBA Script - AWR Scripts - AWR...
View ArticleClik here to view.
Strmount failed in streaming out cell
Hi, I would be grateful if you can help me with this error which I get after trying to run an EMX simulation on a PCELL.I've found very limited information in this forum. Thanks
View ArticleClik here to view.
CPW ports
Hi, in EMX I'm trying to define the ports of a CPW line as suggested in one document of the support area (i.e. P1:Gright,Gleft). The EMX simulation works fine. When I generate the schematic, I get...
View ArticleClik here to view.
Harmonic Balance (HB) Large-Signal S-Parameter (LSSP) simulation
Dear all,Hi!I'm trying to do a Harmonic Balance (HB) Large-Signal S-Parameter (LSSP) simulation to figure out the input impedance of a nonlinear circuit.Through this simulation, what I want to know is...
View ArticleClik here to view.
Error when trying to generate SUL license (-8)
Hi, newbie here.We are using AWR Design Enviroment in our university and so I have to install it (OS: Arch Linux)I installed it in a Windows 10 VM without problems.When I try to start it prompts...
View ArticleClik here to view.
VAR("") does not work within some expressions
Hi,My Virtuoso and Spectre Version: ICADVM20.1-64b.NYISR30.2I have an expression where the EvalType is "sweeps". Here is the expression (I also attached the...
View ArticleCrystal Oscillators
Hello, Currently i am designing a 96MHZ crystal oscillator using pierce topology and also I use for amplitude gain control circuit for regulation. The problem is when i run a PSS + Pnoise i get these...
View ArticleClik here to view.
Error in cds_srr (line 20)
Hi, In the MATLAB, I am using cds_srr and cds_innersrr commands. Although I set the path to the spectre root, I face this error:One or more output arguments not assigned during call to...
View ArticleClik here to view.
Measuring DDJ (data dependent jitter). Cross function on eye-diagram
Hi,My Virtuoso and Spectre Version: ICADVM20.1-64b.NYISR30.2I plot an eye diagram using a built in function. I want to see the data-dependent jitter. I want to measure the eye diagram edges at zero...
View ArticleEVM and constellation of mixer
Hello,I am trying to design an RF mixer for a TX.Assume my input IF signal is at 1 GHz, my LO at 2 GHz and I want my RF at 3 GHz, and assume that the mixer fully works after testing it with HB.How to...
View ArticleClik here to view.
nport device S-parameter data file relative path
Hi,In our design team, we're looking for a strategy to make all cell views self-contained. We are struggling to do so when nport devices are involved.The nport file requires a full path, whereas what...
View ArticleClik here to view.
unbound variable freq
I want to plot the inductance through formula L1=(imag(Z(1,1))/(2*pi*freq)), but the system tells me that the freq is unbound variable? What can I do?
View ArticleClik here to view.
IIP3 of Gilbert cell mixer
HiI'm learning Hb analysis for the IIP3 simulation of a gilbert mixer. My f_RF=5GHz, f_LO=4GHz and f_IF=1GHz . I'm a bit confused about setting the 1st order and 3rd order harmonic at the Direct plot...
View ArticlePSS Shooting - High Q crystal oscillator - Simulator by mistake detects a...
Hi *, I am simulating a 32kHz high Q crystal oscillator with a pulse shaping circuit. I set up a PSS analysis using the Shooting Newton engine. I set a beat frequency of 32k and used the crystal output...
View ArticleClik here to view.
HB: duplicated frequencies in 3-tone simulation
I get multiple results at the same frequency in a 3-tone simulation.I try to determine the IP3 of a mixer. I have 3 large signal tones: 0.75 GHz, 1.25 GHz and 1.26 GHz.At the IM3 frequency of 490 MHz I...
View ArticleClik here to view.
Colpitts Oscillator output power simulation
Hello everybody,As you can find in the attached image, I am trying to simulate a Colpitts oscillator. However, using pss analysis it shows a high output power. My question is where is the problem of my...
View ArticleClik here to view.
Load Pull transistor simulation
Hello everyone,I am trying to perform a load pull simulation of a transistor to verify some gain calculations I made using its S-parameters. Specifically, I have calculated the optimal conjugate...
View ArticleClik here to view.
Getting error while adding element in AWR software
While adding an element created from a netlist file in AWR, I am getting the error 'The element type being dropped is not compatible with the window it is being dropped into'. The netlist file in AWR...
View ArticleCross-coupled oscillator Stability simulation
Hello everyone,For my cross-coupled oscillator design, I have a problem with stability analysis. Based on my achieved results which are attached, where is my design...
View ArticleEMX - EM simulation for large CMOS chip
Hi everyone,I'm currently working on my thesis, which involves a beamformer system using CMOS 65nm technology. I'm trying to use the EMX tool for EM simulation but have encountered a few problems....
View ArticleFigures missing in the RF Design Blogs article of "Measuring Fmax for MOS...
Hi I noticed that some figures from the old posts in the cadence blogs have been missing.I think this problem happened before and Andrew Beckett asked the original author to fix the issue: Figures...
View ArticleTransient Simulation waveform abnormal
Hello EverybodyRecently, I want to design a high output Power Amplifier at 2.4GHz using TSMC 1P6M CMOS Bulk Process. I use its nmos_rf_25_6t transistor model to determine the approximate mosfet sizeI...
View ArticleUsing "nport" as a schematic circuit component
Hello everybody,I designed an inductor in HFSS and extracted its S-parameters. Now, I want to employ this inductor in my oscillator schematic design in cadence.How can I use "nport" component in my...
View ArticleN-path mixer power conversion gain calculation with PSS+PAC
I’m simulating an N-path mixer using ideal components. After performing a PSS+PAC analysis, I observed a positive power conversion gain, while I expected to see a power conversion loss instead. It's...
View ArticleHB tstab randomly giving bad results compared to regular transient
Spectre version: 23.1.0.403_ISR6Virtuoso: 23.1.ISR6*can't upload images for some reason.While running a harmonic balance configured like this:1. Run transient - Decide automatically.2. Run Envelope...
View Article